Skar Audio IX-10 D2 10″ 400 Watt Max Power Dual 2 Ohm Car Subwoofer

Skar Audio IX-10 D2 - 2" basv premium voice coil. Max power: 400 watts. Advanced air flow cooling system. Pressed paper high strength cone. Rms power: 200 watts. The ix series is the perfect solution if you're looking for a price friendly, affordable, and clean subwoofer setup in your vehicle. Featuring a single slug premium ferrite magnet, combined with a two-inch high quality voice coil, the driving force behind this conservatively rated woofer line raises industries standards in what to expect out of a driver in this class.

Skar audio developed the ix series 10-inch subwoofers to be the most powerful, affordable, and reliable drivers in their power class. This ix subwoofers were designed to be both extremely efficient as well, and work great in both vented and sealed applications. Dual 2 ohm voice coil. Rms power : 200 watts, max power : 400 watts, fs : 35.

Skar Audio IX-10 D2 10" 400 Watt Max Power Dual 2 Ohm Car Subwoofer - 7 hz, re : 4. 0 ohms, spl : 86. 3 db, qms : 6. 41, qts : 055, qes : 06, rms : 3. 0 kg/s, cms : 0

More information about Skar Audio IX-10 D2

Skar Audio RP-350.1D Monoblock Class D MOSFET Amplifier with Remote Subwoofer Level Control, 350W

Skar Audio RP-350.1D - Featuring 4-way protection circuitry and 8 AWG Power & Ground Input Terminals for Maximum Current Flow. Class d mosfet monoblock Power Amplifier. Skar audio engineered the RP-3501d class d monoblock subwoofer amplifier to be dominant in both power and reliability compared to anything else on the market in its' class and physical size.

Conservatively rated at 350 watts rMS power at a 1-ohm load, with the capabilities of reaching beyond 388 watts at max power output. Peak power at 1 ohm: 388 watts | rmS Power at 1 Ohm: 350 Watts. This amplifier comes with a remote subwoofer level control bass knob allowing the user to have full control over their bass from the front of the vehicle.

Skar Audio RP-350.1D Monoblock Class D MOSFET Amplifier with Remote Subwoofer Level Control, 350W - Highly efficient Heatsink Design allows for Maximum Reliability & Performance. In addition to all of the above features, the 8 gauge power and ground terminals found on the amplifier allow for maximum current flow and therefore higher power output and more efficient operation. This compact, small footprint amplifier, is by far one of the most affordable monoblocks we have ever released, and is great for powering a pair of subwoofers rated around 200 watts rms each or a single subwoofer around 400 watts rms.

Frequency response: 20hz - 250hz, on-board Bass EQ Switch with +6 or +12dB boost at 45Hz. Furthermore, and variable adjustment tunings for gain level, low-pass filter, +12dB, +6, you'll have full reign over your amplifier with the built-in user control panel, featuring a bass EQ switch 0, and subsonic filter.

Featuring 4-way protection circuitry, low voltage, you'll have the peace of mind knowing that you are protected against damage to the amplifier for various reasons - including electrical shortage, over heating, and more.

More information about Skar Audio RP-350.1D


Similar products



SoundBox Connected 4 Gauge Amp Kit Amplifier Install Wiring Complete 4 Ga Installation Cables 2200W

SoundBox Connected ECK4 - Black/white triple shielded Twisted Pair RCA Interconnect: 17 Feet. Installation accessories/ Connectors / Terminals, Wire Ties and Wire Loom Included. 16 gauge brown/silver speaker wire: 17 Feet / 18 Gauge Blue Remote Wire: 18 Feet. Peak power at 1 ohm: 388 watts | rmS Power at 1 Ohm: 350 Watts. Inline agu fuse holder w/ 80 amp AGU Fuse / Protective Black Wire Loom.

Highly efficient Heatsink Design allows for Maximum Reliability & Performance. Frequency response: 20hz - 250hz, on-board Bass EQ Switch with +6 or +12dB boost at 45Hz. Featuring 4-way protection circuitry and 8 AWG Power & Ground Input Terminals for Maximum Current Flow. General features:  2300 watts peak power rating complete 4 gauge amp install kit heat resistant wire jacket premium heat durability in-line agu fuse holder triple shielded rca interconnect cable premium grade cables   what's included:  4 gauge red cca copper clad aluminum power Wire: 17 Feet 4 Gauge Black CCA Copper Clad Aluminum Ground Wire: 3 Feet Black/White RCA Interconnect: 17 Feet 16 Gauge Brown/Silver Speaker Wire: 17 Feet 18 Gauge Blue Remote Wire: 18 Feet Protective Black Wire Loom Inline AGU Fuse Holder 80 Amp AGU Fuse Installation Accessories/ Connectors Terminals, Wire Ties and Wire Loom Included Authorized Internet Retailer 1 Year Manufacturer's Warranty Please Note:  Bulk Packaged.

SoundBox Connected 4 Gauge Amp Kit Amplifier Install Wiring Complete 4 Ga Installation Cables 2200W - Not for Resale. Wire is not awg american wire gauge. 4 gauge red cca copper clad aluminum power wire: 17 Feet / 4 Gauge Black CCA Copper Clad Aluminum Ground Wire: 3 Feet. Stable at 1 ohm | Remote Subwoofer Level Control Included.

More information about SoundBox Connected ECK4


Similar products



Skar Audio TWS-01 1-Inch 240 Watt Max Power Neodymium Silk Dome Tweeters, Pair

Skar Audio TWS-01 - Featuring 4-way protection circuitry and 8 AWG Power & Ground Input Terminals for Maximum Current Flow. Stable at 1 ohm | Remote Subwoofer Level Control Included. Sensitivity : 92 db. Frequency response : 2. 0 khz - 20 kHz. Frequency response: 20hz - 250hz, on-board Bass EQ Switch with +6 or +12dB boost at 45Hz.

Peak power at 1 ohm: 388 watts | rmS Power at 1 Ohm: 350 Watts. Installation accessories/ Connectors / Terminals, Wire Ties and Wire Loom Included. Frequency response: 2. 0 khz - 20 khz, max power: 240 watts pair, RMS power: 80 watts pair. Black/white triple shielded Twisted Pair RCA Interconnect: 17 Feet. Pair of 1-inch high performance silk dome tweeters with neodymium magnets.

Skar Audio TWS-01 1-Inch 240 Watt Max Power Neodymium Silk Dome Tweeters, Pair - These tweeters make for a great addition to any vehicle, whether being used in conjunction with radio power or amplified power to really allow them to come alive. Sold as a pair. Inline agu fuse holder w/ 80 amp AGU Fuse / Protective Black Wire Loom. Max power : 240 watts pair / RMS power : 80 watts pair. The powerful neodymium magnets of these tweeters allow for added sensitivity and extreme power handling capability.

The tws-01 are 1-inch silk dome component tweeters engineered by scar audio to deliver the ultimate experience in high frequency sound reproduction.

More information about Skar Audio TWS-01


Similar products



RIOT 1100 Watts, Mosfet Monoblock Power Amplifier R1100M

BOSS AUDIO R1100M - Inline agu fuse holder w/ 80 amp AGU Fuse / Protective Black Wire Loom. Max power : 240 watts pair / RMS power : 80 watts pair. Pair of 1-inch high performance silk dome tweeters with neodymium magnets. This amplifier is designed to run your subwoofers giving them the power that they need to perform as they were meant to.

Shift your audio experience up a gear with the Boss Audio Riot R1100M Class A/B Monoblock Amplifier. High level inputs: speaker level inputs are commonly referred to as high-level inputs. Power: maximum power output of 1100 watts at 2 ohms into one channel. Frequency response: 20hz - 250hz, on-board Bass EQ Switch with +6 or +12dB boost at 45Hz.

RIOT 1100 Watts, Mosfet Monoblock Power Amplifier R1100M - Installation accessories/ Connectors / Terminals, Wire Ties and Wire Loom Included. Sensitivity : 92 db. Frequency response : 2. 0 khz - 20 kHz. Customize the sound with Variable Low Pass Crossover and Bass Boost. 4 gauge red cca copper clad aluminum power wire: 17 Feet / 4 Gauge Black CCA Copper Clad Aluminum Ground Wire: 3 Feet.

Variable bass boost: variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.

More information about BOSS AUDIO R1100M


Similar products



A Car Amplifier Wiring Kit Helps You Make Connections and Brings Power to Your Radio, Subwoofers and Speakers - BOSS Audio KIT2 8 Gauge Amplifier Installation Wiring Kit

BOSS AUDIO KIT-2 - Variable bass boost: variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it. Pair of 1-inch high performance silk dome tweeters with neodymium magnets. 8 gauge amplifier installation kit includes: Class d mosfet monoblock Power Amplifier. 5/16" ring terminals, 1/4" Ring Terminals, 4 Speaker Terminals.

High level inputs: speaker level inputs are commonly referred to as high-level inputs. Low-pass crossover: a low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. Black/white triple shielded Twisted Pair RCA Interconnect: 17 Feet. Max power output of 550 Watts at 4 Ohms into one Channel.

A Car Amplifier Wiring Kit Helps You Make Connections and Brings Power to Your Radio, Subwoofers and Speakers - BOSS Audio KIT2 8 Gauge Amplifier Installation Wiring Kit - Warranty: boss audio systems provides a powerful 6 Year Platinum Online Dealer Warranty so long as the purchase is made through Amazon Dot Com. Peak power at 1 ohm: 388 watts | rmS Power at 1 Ohm: 350 Watts. Sensitivity : 92 db. Frequency response : 2. 0 khz - 20 kHz. 20 foot high performance RCA Interconnect, 6 Foot Split Loom Tubing.

Frequency response: 20hz - 250hz, on-board Bass EQ Switch with +6 or +12dB boost at 45Hz.

More information about BOSS AUDIO KIT-2


Similar products



InstallGear 4 Gauge Complete Amp Kit Amplifier Installation Wiring Wire

InstallGear IG4AKR - Peak power at 1 ohm: 388 watts | rmS Power at 1 Ohm: 350 Watts. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers. It can be installed in a variety of different places due to its' slim and compact design. Featuring 4-way protection circuitry and 8 AWG Power & Ground Input Terminals for Maximum Current Flow.

. Low-pass crossover: a low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. 20 4" wire ties, 3 Rubber Grommets. 5/16" ring terminals, 1/4" Ring Terminals, 4 Speaker Terminals. Max power output of 550 Watts at 4 Ohms into one Channel. Speaker level inputs will be used to connect the R1100M to your factory radio or an aftermarket radio that does not have low-level RCA inputs.

InstallGear 4 Gauge Complete Amp Kit Amplifier Installation Wiring Wire - 20 foot high performance RCA Interconnect, 6 Foot Split Loom Tubing. Frequency response: 20hz - 250hz, on-board Bass EQ Switch with +6 or +12dB boost at 45Hz. Inline agu fuse holder w/ 80 amp AGU Fuse / Protective Black Wire Loom. Pair of 1-inch high performance silk dome tweeters with neodymium magnets. Warranty: boss audio systems provides a powerful 6 Year Platinum Online Dealer Warranty so long as the purchase is made through Amazon Dot Com.

Black/white triple shielded Twisted Pair RCA Interconnect: 17 Feet.

More information about InstallGear IG4AKR


Similar products



Skar Audio SK-M5001D Compact Monoblock Class D MOSFET Car Amplifier, 500W

Skar Audio SK-M5001D - Low level inputs: line level inputs, also known as rca inputs or low-level inputs, use RCA interconnect cables to link the R1100M with the source unit. 8 gauge power and Ground Input Terminals. It can be installed in a variety of different places due to its' slim and compact design. 4 gauge red cca copper clad aluminum power wire: 17 Feet / 4 Gauge Black CCA Copper Clad Aluminum Ground Wire: 3 Feet.

Featuring 4-way protection circuitry and 8 AWG Power & Ground Input Terminals for Maximum Current Flow. You will use the Low-pass filter to primarily keep high notes out of your subwoofers. Warranty: boss audio systems provides a powerful 6 Year Platinum Online Dealer Warranty so long as the purchase is made through Amazon Dot Com.

Skar Audio SK-M5001D Compact Monoblock Class D MOSFET Car Amplifier, 500W - 5/16" ring terminals, 1/4" Ring Terminals, 4 Speaker Terminals. The sk-m5001d was engineered to be compact, but provide the power and reliability expected out of larger amplifiers. 17ft soft touch 2-Channel RCA Cable. Anl fuse holder with 100A Fuse. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers.

Peak power at 1 ohm: 388 watts | rmS Power at 1 Ohm: 350 Watts. Amplifier dimensions: 7.

More information about Skar Audio SK-M5001D


Similar products



PAC LC-1 Remote Amplifier Level Controller

PAC LC-1 - Variable bass boost: variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it. 17ft soft touch CCA Speaker Wire. Compact housing allows the unit to be mounted virtually anywhere so control is at the user’s fingertips. Frequency response: 20hz - 250hz, on-board Bass EQ Switch with +6 or +12dB boost at 45Hz.

Warranty: boss audio systems provides a powerful 6 Year Platinum Online Dealer Warranty so long as the purchase is made through Amazon Dot Com. 3ft black soft touch 4 Gauge CCA Ground Cable. 16 foot / 18 gauge blue turn-on wire, 30 Foot / 16 Gauge Speaker Wire. Hi-level input connection: Yes | Signal-to-Noise Ratio Sensitivity: 85dB.

PAC LC-1 Remote Amplifier Level Controller - 20 4" wire ties, 3 Rubber Grommets. Dimensions: the r1100m is 9. 1 inches in depth, 104 inches in Width and 2. 3 inches in Height. Speaker level inputs will be used to connect the R1100M to your factory radio or an aftermarket radio that does not have low-level RCA inputs. You will use the Low-pass filter to primarily keep high notes out of your subwoofers.

8 gauge power and Ground Input Terminals.

More information about PAC LC-1


Similar products



PIXNOR DIY Home Car Stereo 2-Way Speaker Box Terminal Binding Post Round Screw Cup Connector Subwoofer Plug Black

Pixnor® 14756265014-1 - 16 foot / 18 gauge blue turn-on wire, 30 Foot / 16 Gauge Speaker Wire. Dimensions: the r1100m is 9. 1 inches in depth, 104 inches in Width and 2. 3 inches in Height. You will use the Low-pass filter to primarily keep high notes out of your subwoofers. Adds subwoofer level controls to any head unit. Material: durable plastic, copper and gold-plated metal.

Cutout diameter: about 45mm 1 7/8 "; overall diameter: about 75mm 3"; Top-mount depth: 20mm 7/8". 17ft soft touch CCA Speaker Wire. Surface, angle and flush mountable design. Material: durable plastic, copper and gold-plated metal. 17ft soft touch 2-Channel RCA Cable. Cutout diameter: about 45mm 1 7/8 "; overall diameter: about 75mm 3"; Top-mount depth: 20mm 7/8".

PIXNOR DIY Home Car Stereo 2-Way Speaker Box Terminal Binding Post Round Screw Cup Connector Subwoofer Plug Black - 20 4" wire ties, 3 Rubber Grommets. Low level inputs: line level inputs, also known as rca inputs or low-level inputs, use RCA interconnect cables to link the R1100M with the source unit. Variable bass boost: variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.

Color: mainly black. Positive red and negative Black indicators to ensure proper wiring.

More information about Pixnor® 14756265014-1


Similar products



SoundBox 4 Gauge Amp Kit Amplifier Install Wiring & 2.5 Farad Digital Capacitor, 2300W Peak

SoundBox SCAP2D+ECK4 - 3 foot - 8 gauge Black Ground Cable. Speaker level inputs will be used to connect the R1100M to your factory radio or an aftermarket radio that does not have low-level RCA inputs. Anl fuse holder with 100A Fuse. Highly efficient Heatsink Design allows for Maximum Reliability & Performance. Gold-plated contacts for optimal signal transfer.

Screw type terminals ensure a tight and secure connection. Rear connections use quick disconnect connectors. Hi-level input connection: Yes | Signal-to-Noise Ratio Sensitivity: 85dB. Max power output of 550 Watts at 4 Ohms into one Channel. 5/16" ring terminals, 1/4" Ring Terminals, 4 Speaker Terminals. General features:soundbox combined amp kit & Capacitor PackageGive Your System the Wires It Needs and the Capacitor It WantsSoundBox 2.

5 farad digital capacitorsoundbox 4 gauge Complete Install KitAuthorized Internet Dealer1 Year Manufacturer's WarrantyItem Specification- Capacitor:2. 5 farad digital capacitor2500 watts peak power ratingdigital display readoutitem specification- amp kit:complete 4 Gauge Amp Install Kit2300 Watts Peak Power RatingHeat Resistant Wire JacketPremium Heat Durability In-Line AGU Fuse HolderTriple Shielded RCA Interconnect CablePremium Grade Cables What's Included:SoundBox 2.

SoundBox 4 Gauge Amp Kit Amplifier Install Wiring & 2.5 Farad Digital Capacitor, 2300W Peak - 5 farad digital capacitor 4 gauge red cca copper clad aluminum power wire: 17 feet4 gauge black cca copper clad aluminum ground wire: 3 feetblack/white rca interconnect: 17 Feet16 Gauge Brown/Silver Speaker Wire: 17 Feet18 Gauge Blue Remote Wire: 18 FeetProtective Black Wire LoomInline AGU Fuse Holder80 Amp AGU FuseInstallation Accessories/ ConnectorsTerminals, Wire Ties and Wire Loom Included Class d mosfet monoblock Power Amplifier.

High level inputs: speaker level inputs are commonly referred to as high-level inputs.

More information about SoundBox SCAP2D+ECK4


Similar products

Bookmark the permalink.

Comments are closed